760-840-590 - Hydraulic Excavator, Truck Mounted (6x6), 41,000 lbs. operating weight, minimum

NOTE:

This detailed specification is not complete unless it is used in conjunction with all conditions of the Technical Specifications.

INTENDED USE:

USED PRIMARILY FOR DITCH CLEANING AND EXCAVATING APPLICATIONS.

CARRIER

ENGINE:

A.

Diesel engine, liquid cooled, with a minimum of 210 Gross HP (per the latest issue of SAE J1349), and a minimum displacement of 8.3L.

B.

Permanent anti-freeze and corrosion protection.

C.

Dry type air cleaner with service (restriction) indicator.

ELECTRICAL:

A.

Minimum 100 amp 12-volt alternator.

B.

Battery to have a minimum total of 1150 CCA @ 0 degrees F.

TRANSMISSION:

Direct drive manual transmission, ten forward speeds, minimum. Fuller RT 8908LL or approved equivalent. Minimum 14 inch diameter two-plate clutch.

TRANSFER CASE:

Transfer case with cab-control front axle declutch.

AXLES & SUSP.:

A.

Steel front drive axle and suspension, minimum 16,000 lb. GAWR.

B.

Single speed, tandem drive rear axle with a driver controlled inter-axle and differential lock, minimum 40,000 lb. GAWR. Rear suspension must have minimum 54 inch steel walking beams.

NOTE: The rear axle ratio is to be selected by the Contractor in accordance with the engine and transmission provided. A ratio that will provide the maximum possible reduction as well as a minimum top speed of 55 MPH on a level grade.

PERFORMANCE:

A.

Factory installed speedometer, odometer, ammeter or voltmeter, fuel gauge, engine oil pressure gauge, coolant temperature gauge, tachometer, air pressure gauge and dash-mounted engine hourmeter.

B.

Power steering.

COMFORT ITEMS:

A.

Air conditioner, heater and defroster.

B.

Sunvisor.

C.

Tinted safety glass all windows.

SAFTEY ITEMS:

A.

Horn(s), electric.

B.

Large West Coast type mirrors, to include lower convex spot mirrors on both sides.

C.

Automatic-adjustable volume backup alarm (may be provided and installed by the Contractor, if not available from the Manufacturer), per the latest issue of SAE J994.

D.

Rain Flaps: Splash and spray suppressant rain flaps, straight grass type, to be installed on heavy-duty hangers (may be provided and installed by the Contractor, if not available from the Manufacturer).

NO CONTRACTOR ADVERTISING, OR IDENTIFICATION, WILL BE PERMITTED ON RAIN FLAPS.

E.

Turn signals, front and rear, with traffic hazard warning switch.

F.

Windshield wiper, windshield washer, lights, and reflectors shall be according to ICC and all other State and Federal regulations.

G.

One 10-lb. hand held fire extinguisher mounted inside cab.

H.

All access steps shall be self-cleaning slip-resistant grating.

BRAKES:

A.

Air brake system.

B.

Spring applied parking brake.

C.

Front and rear automatic slack adjusters.

D.

Low air pressure warning indicator.

E.

Air dryer with heater. Bendix AD-9, AD-IP, AD-IS, Wabco System Saver 1200 or approved equivalent.

TIRES & WHEELS:

A.

Front tires: (2) 385/65R22.5J (18PR) with highway tread.

B.

Rear tires: (8) 11R22.5G (14 PR) with on/off road or all-terrain tread.

C.

All wheels to be one-piece steel disc, 10-hole, 22.5 inch diameter.

CHASSIS, FRAME:

A.

171 inch wheel base, minimum.

B.

Front and rear tow hooks.

C.

Standard front bumper.

CAB EQUIPMENT:

A.

Air suspension driver seat.

B.

Cab assist handles both sides.

C.

Vandal protection, including locks for cab door(s), engine compartment, and exposed (outside of locked cab or locked engine compartment) battery box and fluid caps.

UPPERSTRUCTURE

ENGINE:

1

Diesel engine, four cylinder, four cycle, liquid cooled, minimum 110 Gross HP, per the latest issue of SAE J1349.

2

Displacement, minimum 3.9L.

3

Permanent anti-freeze.

4

Dry type air cleaner with service (restriction) indicator.

5

Factory installed ammeter or voltmeter, engine oil pressure and coolant temperature gauges, engine hourmeter, and air pressure gauge and warning indicators. Or (preferably), an electronic monitoring system for as many of these functions as possible, with gauges for the remainder.

ELECTRICAL:

1

Minimum 105 amp 12-volt alternator.

2

Batteries to have a minimum total of 1200 CCA @ 0 degrees F.

3

Manual master battery disconnect switch.

CAB:

1

Fully enclosed all weather cab with maximum cab heat and sound insulation, 3-way adjustable seat, and factory-tinted safety glass all around, skylight, air conditioner, heater and defroster.

2

Vandal protection, including locks for cab door(s), engine compartment, and exposed (outside of locked cab or locked engine compartment) battery box and fluid caps.

3

Hydraulic system to provide independent swing and remote control travel.

4

Visual hydraulic oil level gauges on reservoir.

5

Toolbox, lockable, and all special tools needed to operate, adjust or maintain the machine.

6

Hydraulic Joy Stick controls for all upperstructure movement.

REMOTE CONTROLS:

Separate controls shall be provided in the upper cab for remote operation of the carrier. Controls shall provide propel, steering and brake functions.

BUCKET:

60 inch, Quick-Change ditching bucket, with a struck capacity (per latest issue of SAE J296) of 0.62 cubic yard, minimum.

PERFORMANCE:

(with the machine equipped per this base specification, per the latest issues of SAE J1057, J1116, and J1234).

1

Travel height of complete machine not to exceed 13 feet 6 inches, and travel width of complete machine not to exceed 8 feet (except for front axle/tires/wheels).

2

360 degree continuous swing, left and right.

3

Bucket tilt to be done hydraulically.

4

Lift capacity on rubber, over side, with 60 inch bucket, without boom extension, at 20 feet radius, 5 feet above ground level, per the latest issue of SAE J1097, 3,450 lbs. min.

5

Dimensions, with the 60 inch ditching bucket in a single adjustment position, per the latest issue of SAE J1193:

(a) Swing clearance, rear of upperstructure (i.e. tail swing), 8 feet, maximum.

(b) Ground clearance per latest issue of SAE J1234, 8 inches minimum.

(c)Maximum radius at groundline (i.e. surface reach) (must be adjusted for actual bucket radius on 60 inch ditching bucket), 27 feet, minimum.

(d) Maximum digging depth (without boom extension), 16 feet, minimum.

(e) Bucket pivot angle (i.e. sweep angle), 150 degrees minimum.

(f) Telescoping travel, 10 feet minimum.

(g) Bucket tilt angle (both sides of center), 90 degrees minimum (i.e. 180 degrees total). Bucket rotation angle, 180 degrees minimum, if applicable.

(h) Minimum clearance of bucket at maximum boom height (i.e. loading height) (with boom at maximum angle, with bucket fully retracted, and no boom extension), 11 feet, minimum.

(i) Boom pivot angle (over rear), 30.0 degrees above horizontal and 55.0 degrees below horizontal, minimum.

6

Total advertised machine operating weight, per the latest issue of SAE J1234, of 41,000 lbs. minimum.

7

The rated tangential (breakout) force with 60 inch ditching shall be a minimum of 14,500 lbs., per SAE J1179.

8

The rated boom crowd force shall be a minimum of 13,000 lbs.

SAFTEY ITEMS:

1

Windshield wiper(s) and washer(s).

2

Electric travel alarm, per latest issue of SAE J994, for remote control operation in either direction.

3

Electric warning horn, per latest issue of SAE J1105, or air horn.

4

Safe access to machine cab and servicing points to be in accordance with the latest issue of SAE J185.

5

Safety signs per latest issue of SAE J115.

6

Provisions to prevent unauthorized starting or movement of machines, per latest issue of SAE J1083.

7

Remote control transmission neutral safety start device.

8

“Dead-man” type self-centering controls to stop movement when released.

9

Cab assist handle(s) at each door.

10

One 10-lb. hand held fire extinguisher mounted inside cab.

PAINT:

Manufacturer’s standard paint and color, factory painted.

CONDITIONS:

1

The services of a factory technician, thoroughly trained in the use and operation of the unit, shall be furnished for a period of not less than one (1) day and up to (2) days, if requested by the Eligible User, to instruct personnel in the use, operation and maintenance of the unit after delivery. This is to be done at the delivery location.

2

At a minimum, the Manufacturer’s standard warranty for state and municipalities shall be provided. A copy of the warranty shall be provided with the bid.

3

The Contractor shall provide any and all non-specified features or components necessary in order to provide a complete unit.

COMMODITY NO.

DESCRIPTION

760-840-590

HYDRAULIC EXCAVATOR, TRUCK MOUNTED, 41,000 LBS. OPERATING WEIGHT, MINIMUM (6X6)

Total Cost of Ownershipwith Guaranteed Maintenance and Repurchase

LIFE CYCLE ANALYSIS

Contractor

No Award

Leasing

Contractor

No Award

Purchase

Contractor

JOE MONEY MACHINERY CO., INC.

Discount*

($1,250)

Model

BADGER 460http://www.badgerequipment.com/460/460.htm

Price

$240,400.00

Percentage discount off the current Manufacturer’s Suggested Retail Price for non-specified options for the model bid. The percentage discount is applied to the Manufacturer’s Suggested Retail Price to determine the actual price of an option.

DISCOUNT %

7%

CURRENT MSRP DATE

7/1/2005

*Discount for equipment picked up by ordering Eligible User at Contractor’s place of business.

Approximate delivery time required ARO:

DELIVERY ARO 120 TO 180 DAYS

Note to users:Options are listed for the purchase of this equipment only!Purchasers needing options for lease equipment or Total Cost acquisitions are to negotiate option prices with Contractors.

760-840-590

HYDRAULIC EXCAVATOR, TRUCK MOUNTED, 41,000 LBS. OPERATING WEIGHT, MINIMUM (6X6)

OPTIONS:

1001

High efficiency bypass oil purification system. This system is designed to reduce or eliminate engine oil changes and extend its useful life. The Puradyn Oil Filtration System or approved equivalent. Puradyn Filter Technologies, Inc. 1-800-488-0577. Bid for carrier engine only.

PRICE

$995.00

1002

High efficiency bypass oil purification system. This system is designed to reduce or eliminate engine oil changes and extend its useful life. The Puradyn Oil Filtration System or approved equivalent. Puradyn Filter Technologies, Inc. 1-800-488-0577. Bid for upper engine only.

PRICE

$995.00

1003

Delete front driving axle and transfer case (6x4 model). Include highway tread front tires in lieu of on/off road or all-terrain tread.

PRICE (CREDIT)

($20,600.00)

1004

Synthetic lubricant for front driving axle, rear differentials, transfer case and transmission.

PRICE (BASE)

$500.00

PRICE (OPT 1003)

$450.00

1005

Automatic lubrication system. System shall consist of an electronically operated pump metering Class 2 lubricant to each lubrication point. Groeneveld, Vogel Automatic Lubrication System of approved equivalent. Groeneveld Atlantic South, Inc. (813) 626-5600, Vogel Lubrication, Inc. (757) 380-8585, email: vogel@vogel-lube.com.

PRICE

$7,800.00

1006

High efficiency bypass oil purification system. This system is designed to reduce or eliminate hydraulic oil changes and extend its useful life. The Puradyn Oil Filtration System or approved equivalent. Puradyn Filter Technologies, Inc. 1-800-488-0577.

PRICE

$995.00

1007

Delete carrier cab air conditioner.

PRICE (CREDIT)

($3,225.00)

1008

Delete upper cab air conditioner.

PRICE (CREDIT)

($3,170.00)

1009

Special state color, DOT Yellow, Federal Yellow No. 13538, DuPont #L9069A, ACME No. 2712, Deere No. PT102, or approved equivalent, (may be Contractor painted if factory painting is not available). NOTE: The entire unit, including options, shall be painted the same color.

PRICE

$2,000.00